Author: blogger

Motorcycle Repair Restoring Your Bike

Posted on by blogger

Soaring fuel prices have made gas-guzzling cars very unpopular. Welcome to the resurgence of the motorcycle. Why? Because properly maintained motorcycles and motorcycle engines can get between 40 and 60 miles a gallon. Smaller scooters get upwards of 90 miles a gallon, pretty good for an economy with $4-per-gallon gasoline.

Because of this, bike sales have soared. Motorcycle repair, too, can come in handy. Do you have a bike in storage that you haven’t dusted off for awhile? There’s a good chance you can be among those restoring motorcycles so that you can ride your old road hog again.

Restoring your older motorcycle to working condition starts with some basic steps:

Check Fuel
If you didn’t use a fuel stabilizer before you put the bike into storage, drain your old fuel (including tank, fuel lines and carburetor as applicable) before you run the engine, and put new in. Lubricate spark plug ports with a little oil, too, before you start things up.

Check Oil
Change the oil and filter if you didn’t do so before you started. If you did, top levels off.

How Is Your Battery?
Make sure leads are not corroded and that the battery will fully charge and then hold a charge. If it doesn’t, replace the battery.

Inspect The Chain
Because your chain transfers power from the engine to the rear wheel, it is very important that it be in excellent shape. Look the chain over for the following:

— Is the chain the proper tension? You should be able to grasp it in the center and move it about one inch in either direction, up or down.
— Are front and wheel sprocket teeth in good condition? If the teeth have grooves or “waves” in them or they show other signs of wear, you probably need new sprockets (chain will probably show similar wear and need replacement).
— Check every single section of the chain for signs of wear and for proper tension. It should move about an inch when you pull on it. Tighten the chain if it’s loose, and loosen it if it’s tight. If the links themselves are too tight, you might need to replace the whole chain.
— Clean dirt off the chain with a clean towel or rag before you apply lubricant. Make sure you thoroughly lubricate all sprocket teeth and links.
— Lubricate the chain well. Remember that some solvents should not be used with rubber if your chain has rubber parts to it. Use a proper solvent and wipe off any excess lubricant with a clean rag.
— Set chain tension properly by moving your rear wheel and axle forward or backward. Both sides of the axle should be aligned properly before you tighten things up or the chain and sprockets might wear out quickly. Tighten the axle nuts and replace the cotter pin with a new one if needed.

Fluid Levels
Brake, clutch and coolant levels should be checked as necessary. Make sure you replace missing brake fluid with a new container of the same brand you used last time. Let your bike idle for a few minutes before you take off so that all fluids circulate properly.

Tires and Suspension
Inspect everything thoroughly before you take your first ride. If you kept your bike stored upright on a kickstand, make sure your tires aren’t cracked, marked, or flat. In addition, check to make sure tire wear and air levels are good.

Sheet Metal Stamping In The Automotive Industry

Posted on by blogger

Historically, sheet metal stamping has been used extensively to produce automotive body panels. Although sheet metal stamping use has decreased with the advent of fiberglass body panels, sheet metal stamping is still the most popular material for manufacturing automobiles today. The addition of lasers and robotics to the automobile manufacturing process has further expanded the way that sheet metal stamping is processed.

Lasers

Lasers have been used in production facilities since the 1960’s. Today, they are used to cut, form holes, engrave, weld or heat treat sheet metal stamping for use in automotive production.

Lasers are used in applications that rely on precise measurements and exact alignments.

The adjustment of lasers is measured in micrometers, or millionths of a meter.

There are many different types of lasers used to alter sheet metal stamping and plastics in the automotive industry.

Carbon dioxide laser- uses a mixture of carbon dioxide, nitrogen and helium to produce a continuous laser output

Continuous-wave laser- this type of laser produces light beams continuously rather than in controlled pulses

Excimer laser-emits light in a UV spectrum that is used for producing high quality edges on parts that are prone to cracking or thermal damage; it falls into the category of pulsed-gas lasers

Gas laser-any laser that uses a gas mixture as the lasing medium; common gases are argon and carbon dioxide

Pulsed laser-emits light in controlled pulses and is preferred for thin materials ; it can be used to create intricate details and work in tight corners without burning

Ruby laser-a solid state laser that uses a synthetic ruby crystal with a chromium impurity as the lasing medium

Solid-state laser-a type of laser that uses a crystal or glass as the host for an impurity to produce the lasing action; especially useful for precise measuring and spot welding

Yttrium aluminum garnet (YAG) laser-ranges in power from a few milliwatts to more than 400 watts; used for cutting, drilling, heat treating and welding operations

Robotics

Robotics are often used for repetitive tasks, monotonous jobs or those parts of the manufacturing process that are physically difficult or take place in environmentally unpleasant conditions. They are directed by computer programs and perform precise operations without human intervention.

Lasers and robotics have significantly increased the speed at which sheet metal stamping can be processed in the automotive manufacturing process. Continued technological advancements in these two areas will further increase the cost effectiveness and productivity of automotive manufacturing facilities.

How Advertising in Social Networking Sites Helps Your Automotive Business

Posted on by blogger

With the increase in number of social networking users, the Internet has added up another potential arena for marketing online social networking sites. Especially for automotive business, where branding will be the major marketing objective, advertising in social media is not worth ignoring. Here are some benefits of advertising in social networking sites for automotive businesses:

Reaches wider audiences
We are now in an era where an account in social networking site is as important as having a mobile. Facebook alone has 175 million users logging into the site each day. When you place your ad in a social networking site, it is more likely that your ad is watched by a large number of visitors.

Moreover, users are becoming more offended with traditional advertisements as they seem to invade their privacy. The ads in social networking sites may not seem intrusive as they mingle with the flow of conversations in them.

Improves traffic
The effectiveness of target-based advertising has long been recognized by businesses. It is much easier to promote your auto dealership to niche consumer base through wide number of options such as forums, marketplaces and groups on social networking sites. Such targeted online ads are more likely to increase click-through rates of your ads, from potential consumers. Thus, advertising in social networking sites will not only improve your landing page traffic, but also is more likely to convert the traffic into leads.

Builds good reputation
More and more consumers are turning to social networking sites for advice on purchasing their car. There are many credible automotive forums, blogs or groups on sites like Facebook, which have already built their reputation by helping many such people seeking advice. These conversations are re-visited and referred by many others who require similar advice. When your ad is displayed among those conversations, chances are more that you can build good brand reputation out of it.

Highly interactive
Interactive advertising has become one of the popular online advertising techniques today. The best option available for interactive online advertising is social networking sites. Unlike advertising in traditional media, advertising in social networking sites enables auto dealers to interact with their customers.

Post offers and discounts: There are certain social networking sites like Groupon, LivingSocial, Scoutmob, etc. that have become popular these days by allowing businesses to post offers and discounts at faster pace. They already have gained much popularity among consumers, thus leaving enough chances of increasing your advertising ROI.

Your social media marketing campaign can turn more effective, when supported by social networking advertisements. As the ads belong to the same platform that the users are using, it is more likely to get them to subscribe or sign up to your messages. This further helps you achieve your marketing goals easily.

Get feedback instantly: Social media enables two-way interaction between you and your consumers. Queries and feedback related to cars or services from consumers will reach you instantly. However, it is not likely that the feedback is positive always. But responding appropriately and quickly even to a negative feedback, will prove you more credible in the market.

You will require an effective social media strategy to gain success here the major reason most auto dealers do not succeed with it. Since the competition is less, there are more chances that you can use it to your advantage with the help of an experienced social media strategist.

If you are one of those auto dealers, who are still struggling to get enough ROI out of their advertising campaign, the problem might be with the advertising space you are investing in. It is then the right time to move to social networking sites for promoting your auto dealership.

The Benefits Of Using Rebuilt Engines

Posted on by blogger

Many vehicle owners may be unaware it is not always necessary to buy a brand new engine when the old one in their car fails to work. As in clothes and furniture, there are also second hand engines that although may not have the newest parts can still perform its needed functions. These are the so-called rebuilt or remanufactured engines.

Rebuilt engines are those that have been dismantled, checked, cleaned and their parts repaired or replaced for upgrading purposes. Using this type of engine known as repowering is less expensive compared to purchasing a new engine or vehicle and it can even lengthen your cars life if you choose the right one for your vehicle. Some parts may still be the original or they can be slightly used or they can also be brand new. Whats important to remember is to always ask for a warranty from manufacturers. Others may provide a certified staff and checks on used engines or a combination of both.
Involved in the process of rebuilding engines are the reforming of the piston-cylinder system, smoothing and lubricating of all bearings, regrounding of crankshaft or camshaft and connecting of rods that have been gauged. Replacement of other parts including the timing belt and gaskets may also be needed.

A big advantage of using rebuilt engines is its low cost despite the intensive labor that went into manufacturing it. There are many online vendors these days that offer cheap rebuilt and used engines or motors of various brands allowing vehicle owners to gain sufficient savings. Among the popular brands that are in demand are the Ford engines as well as those from Japanese-made vehicles such as Toyota and Honda.

Another benefit of rebuilding engines is the fact that they are now able to meet the latest original equipment manufacturer (OEM) specifications. With improvements in OEM specifications different from the original, your engine has a good chance of running smoother and more efficiently than before.

In line with this trend of using rebuilt engines, the Automotive Repair Council (ARC) is taking steps to inform consumers about the advantages of installing a rebuilt engine and availing of machine shop services instead of buying a new or used vehicle or using a used engine. The council advocates that using a remanufactured engine is as good or even better than the original one. It is now distributing copies of its 16-page consumer booklet to its members in various states while providing relevant information on its website.

If youre one person considering using rebuilding engines or rebuilding your existing engine, Low Mileage Engines can help you. This company sells only certified remanufactured used car and truck engines both domestic and foreign models to include Chevrolet, Cadillac, Audi, Hyundai, BMW, Jeep, Toyota, Nissan and Lincoln. Low Mileage Engines supplies engines with verified mileage via the Carfax mileage verification.

Automotive Parts Suppliers Services Right At Your Doorsteps

Posted on by blogger

Generally, the automotive parts are being considered very expensive for buying. Therefore, to get these parts at the cheaper rates, one should try to do the necessary research either offline or online. One can definitely collect all the required information regarding the various famous automotive parts suppliers via web portals especially dedicated to the field. Some of the very common components of these automobiles that people look for often, include car door, camshaft, crankshaft, clutch, catalytic converter, battery, bumper, belts, brakes, anti lock brake system and the air filter.

Searching for the automotive parts suppliers via online mode has surely made life much easier for number of customers worldwide. One need not to run from the pillar to the post for finding out best quality of the automotive part within the affordable rates. Online shopping of products has made working process simpler. The manufacturers and the wholesalers who have a reputed name internationally have also opened their plants worldwide so as to reach the global customer range. This boosted not only their business but the availability of quality products as well. You can check the products catalogue on their official websites for convenient selection and purchase thereby.

Purchasing of automotive parts via online has various advantages as compared with the traditional stores. With the help of the web and the computer technology, one can easily surf the available online automotive stores right from their home or office. They can even crack some of the best deals with various dealers and the suppliers. One can even draw various comparisons between the services, prices and the various online stores in a matter of just few minutes. There are various automotive parts suppliers who have made their websites so much interactive and convenient that any type of the suggestion and the query can be enquired via Internet.

Most of these websites offers almost all of the required information about the automotive manufacturers, wholesalers, distributors, dealers and the stores. Therefore, before purchasing any of the automotive parts one should consider the warranty, contact details, product quality and the prices. Apart from this information, there are various websites who are providing the basic reviews from the previous customers and the professional agencies which also help in taking decisions very conveniently. Through the online availability of the automotive parts suppliers, one can surely order various parts and can therefore, save lot of time and money.

The online automotive parts suppliers contain various non factory parts, also the used and the after market parts that are very hard to get through the traditional ways of the marketing. The facility of the immediate ordering enhances the online mode of doing shopping more often. Some of the online parts suppliers are also offering various quality assurance and the discounts with the good warranty on the already used or the new components of the auto parts. One can get some of the best automotive parts from various stores available within the prescribed budget. So, this will prove shopping at ones own convenience.